GAUSS Logo Instruments High Speed Emission Measurements
Navigation
  • Products
    • TDEMI ULTRA
    • TDEMI eXtreme
    • TDEMI Mobile+
    • TDEMI Mobile
    • TDEMI G
    • TDEMI S
    • EMI64k
  • Applications
  • Technology
    • RF-/Microwave Circuitry
    • Digital Signal Processing
  • Support
  • Company
    • News
    • About us
    • Publications
    • Partners
Language

Select your language

  • Deutsch
  • English

News

New EMI Receiver Series TDEMI X - Emission Measurements by a factor of 64000 faster

Created: 04 March 2013

GAUSS INSTRUMENTS presents a new series of ultra-fast EMI receivers with the brand name TDEMI eXtreme (short: TDEMI X). The new TDEMI X series provides in addition to the classical EMI receiver mode a huge variety of measurement and analysis functions. Using the leading-edge FPGA technology the measurement times can be reduced by a factor of 64 000. High-resolution giga-samples analog-to-digital converters increase the dynamic range by more than 25 dB in comparison to the previous standard product series TDEMI.

Read more …

TDEMI is setting a new benchmark in Spectrum Analysis

Created: 08 October 2012

The worldwide fastest EMI test receiver TDEMI, covering the frequency range 10 Hz - 40 GHz, which is 4000times faster than previous conventional technologies now also provides a Spectrum Analyzer for measurements according to communication standards. Additionally this spectrum analyzer mode can also be used for ultra fast pre-scanning during EMI measurements.

Read more …

IEEE EMC 2012 Pittsburgh, Pennsylvania

Created: 05 August 2012

GAUSS INSTRUMENTS@the 2012 IEEE International Symposium on Electromagnetic Compatibility in Pittsburgh, Pennsylvania (US), 5th - 10th August 2012. Visit us at booth #923 together with our US distributor EMI Instrumentation and check out our TDEMI® Measurement System with its blazing speed in the frequency range 10 Hz to 40 GHz and its latest features, e.g. APD evaluation. Ultra high-speed measurements according to commercial and military standards up to 40 GHz boosting your EMC compliance and pre-compliance tests into new dimensions.

Read more …

Emission Measurement of ISM Devices with APD

Created: 25 May 2012

The measurement must be performed at several frequencies where the highest emissions have been detected. So far emission measurement by the extension of the CISPR 11 the first time the APD measuring function is defined in a product standard. The Amplitude Propability Density Function (APD) describes a weighting of the interference according to the statistical distribution of the amplitude. The new standard regulates an APD value to be below 0.1 at an electric field strength of 70dBµV/m over the frequency range from 1 GHz up to 18 GHz, excluding the reserved band at 2.4 GHz. Measurements using APD have been extremely time consuming, because the dwell time has to be more than 30 seconds and the measurement has to be repeated at several frequencies. Further the maximum has to be searched by pre-scanning using Max and Hold function.

Read more …

2012 Asia-Pacific Symposium on EMC in Singapore

Created: 16 April 2012

Learn about time-domain EMC measurments and join the Special Session 'Time Domain Measurement of Electromagnetic Interference' at the APEMC Symposium 2012 organized by Professor Dr. techn. Dr. h.c. Peter Russer. The special session offers seven presentations giving introduction and detailed insight into measurement of electromagnetic interference and application of time-domain methods. With three contributions by GAUSS INSTRUMENTS advanced methods for the modern world of EMC testing will be shown, accelerating and simplifying the measurement procedures of more and more complex and challenging devices under test.

Read more …

Page 5 of 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • About us
  • Contact & Legal Information
  • Privacy policy

Your chosen country:

Call us at +49.89.5404699.0